Lapis Lazuli, Lazurite and Natural Ultramarine Blue

MSDS Number 410-15

Section 1: Product and Company Information
Product Name(s) Lapis Lazuli, Lazurite and Natural Ultramarine Blue
Product Number(s) 410-15S, 410-16S, 410-17S, 410-18S, 410-19S
Company Natural Pigments LLC
PO Box 112
Willits, CA 95490
United States of America
Technical Phone 707-459-9998
Fax 707-275-6063
Section 2: Composition / Information on Ingredients
Product Name Lapis Lazuli, Lazurite and Natural Ultramarine Blue
Synonyms lapis lazuli blau, lasurstein blau, bleu d'azur
Source This is a natural product from Afghanistan, Chile or Russia.
Component Name CAS No. % Composition Range OSHA PEL mg/m3 ACGIH TLV mg/m3 NIOSH mg/m3
Chemical Formula     TWA STEL TWA STEL TWA STEL
Sodium Alumino Sulfosilicate
(Na, Ca)8Al6Si6O24(S, SO4)
57455-37-5 50-80 N.E.1 N.E. N.E. N.E. N.E. N.E.
1) N.E. = None Established
Section 3: Hazards Identification
Inhalation
Acute Health Effects Causes irritation to the respiratory tract. Symptoms may include coughing, shortness of breath.
Chronic Health Effects No information available
Aggravation of
Pre-existing Conditions
Persons with respiratory function may be more susceptible to the effects of this substance.
Ingestion
Acute Health Effects Slightly hazardous in case of ingestion.
Chronic Health Effects No information available
Aggravation of
Pre-existing Conditions
Medical conditions that may be aggravated by exposure: None anticipated.
Eye Contact
Acute Health Effects Contact with eye can produce irritation.
Chronic Health Effects Prolonged or repeated contact may produce severe irritation.
Aggravation of
Pre-existing Conditions
Medical conditions that may be aggravated by exposure: None anticipated.
Skin Contact
Acute Health Effects May cause irritation, depending on duration of contact.
Chronic Health Effects No information available
Aggravation of
Pre-existing Conditions
Persons with pre-existing skin problems may be more susceptible to the effects of this substance.
  Health effects described above are based on published scientific information available for review and evaluated on behalf of this product. Actual signs and symptoms experienced may vary due to conditions at the time of exposure.
Section 4: First Aid Measures
After Inhalation Remove to fresh air. If conscious, have victim clear nasal passages. Restore breathing (e.g., artificial respiration, CPR). Seek medical attention, as necessary, if symptoms develop or persist.
After Skin Contact In case of contact, wipe off excess material from skin then immediately flush skin with plenty of water for at least 15 minutes. Wash clothing before reuse. Call a physician, if irritation occurs.
After Eye Contact Holding eyelids open, do not allow victim to rub their eyes. Gently flush eyes for 15 minutes with large quantities of water. Seek medical attention if irritation develops or persists.
After Ingestion Never give anything by mouth to an unconscious person. Do NOT induce vomiting. Get medical attention if symptoms appear.
Section 5: Fire Fighting Measures
Fire Not considered to be a fire hazard. Not flammable.
Explosion Not considered to be an explosion hazard.
Flash Points Not applicable
Auto-Ignition Not applicable
Flammable Limits Not applicable
Extinguishing Media This material is not combustible and is not anticipated to react with commercially employed extinguishing media. Use appropriate extinguishing media for surrounding fire.
Special Fire Fighting Procedure As part of responding to any fire, firefighters should wear full turnout gear with a positive pressure demand mode Self-Contained Breathing Apparatus (SCBA). Contain all fire suppression run-off.
Hazardous Thermal
Decomposition Byproducts
No information available
Fire/Explosion Hazards No information available
Section 6: Accidental Release Measures
Spill Procedures Protect against identified hazards through use of prescribed personal protection equipment, proper work and hygiene practices. Limit foot and vehicular traffic to minimize mechanical agitation and dispersion. Employ a vacuum, equipped with HEPA (High Efficiency Particulate Air) filter, for clean-up of the spill material. If no vacuum is available, use a broom and shovel to collect excess powder in the area. Residual material should then be cleared, utilizing the process of wet sweeping, to avoid dust generation.
Containment Techniques This is a solid material and will not travel far from the spill location unless mechanically agitated. Therefore, no specific containment techniques are recommended outside of restricting access to the spill location. During spill cleanup, residual wash waters should be contained and collected for proper disposal.
Spill Response Equipment The following equipment is recommended for spill response:
• vacuum, equipped with a HEPA filter
• broom, wet mop
• dustpan, shovel, or scoop
• bags, drums, or sacks for collection

Note: Non-sparking equipment may be selected, based on location specific requirements and individual work site evaluations.
Personal Protective Equipment Employees should utilize the following protective equipment when performing spill response activities:
• gloves (rubber or leather)
• cotton or Tyvek coveralls
• chemical/safety impact goggles
• respiratory equipment recommended in Section 8
Section 7: Handling and Storage
Handling When handling this product, all personnel are directed to:
• Wear all specified elements of PPE, as directed by this document, or under location specific requirements, whichever is more conservative.
• Avoid creating dust, where possible.
Storage The following information provides the appropriate and recommended methods for safe storage and maintenance of product integrity:
• Store in a cool, dry, well-ventilated area.
• Product containers (paper bags, nylon bags, drums, etc.) are prone to physical damage. Care should be taken in storage and handling in order to prevent damage.
• Avoid contact with oxidizers and chemically active metals, since violent reactions may occur.
Section 8: Exposure Controls / Personal Protection
Engineering Controls If user operations generate dusts or fumes, use process enclosures, local exhaust ventilation, or other engineering controls to keep airborne levels below recommended exposure limits.
Respiratory Protection If the exposure limit is exceeded and engineering controls are not feasible, a full facepiece particulate respirator (NIOSH type N100 filters) may be worn for up to 50 times the exposure limit or the maximum use concentration specified by the appropriate regulatory agency or respirator supplier, whichever is lowest. If oil particles (e.g. lubricants, cutting fluids. glycerine, etc.) are present, use a NIOSH type R or P filter. For emergencies or instances where the exposure levels are not known, use a full-facepiece positive-pressure, air-supplied respirator. WARNING: Air-purifying respirators do not protect workers in oxygen-deficient atmospheres.
Skin Protection Wear impervious protective clothing, including boots, gloves, lab coat, apron or coveralls, as appropriate, to prevent skin contact.
Eye/Face Protection Use chemical safety goggles and/or full face shield where dusting or splashing of solutions is possible. Maintain eye wash fountain and quick-drench facilities in work area.
Work Hygiene Practices To control potential exposures, avoid creating dust. Always wear appropriate protective equipment when handling. To avoid skin contact, gloves (leather or rubber) should be worn when handling containers of this substance. Do not eat, drink, smoke or apply cosmetics while using/handling. Always wash hands and face after handling.
• Avoid direct skin contact when possible.
• Do not eat, drink, smoke, or perform other hand-to-mouth activities in product use or handling area.
• Wash thoroughly after handling this product.
Section 9: Physical and Chemical Properties
Appearance Physical State: Solid
Color: Blue
Form: Powder or Crystal
Odor Odorless
Molecular Weight No information available
Ph Value Not applicable.
Boiling Point (at 760 mm Hg) Not applicable.
Melting Point No information available (decomposes)
Flash Point Not applicable.
Flammability Not applicable.
Autoignition Temperature Not applicable.
Explosive Properties Not applicable.
Explosion Limits Not applicable.
Vapor Pressure (mm Hg) Not applicable.
Vapor Density (Air=1) Not applicable.
Solubility Insoluble at 20° C.
Specific Gravity (Water=1) 2.3
Viscosity Not applicable.
Evaporation Rate (BuAc=1) Not applicable.
Section 10: Stability and Reactivity
Stability Stable under ordinary conditions of use and storage.
Hazardous Decomposition Products No information available.
Hazardous Polymerization Will not occur.
Incompatibilities No information available.
Conditions to Avoid No information available.
Section 11: Toxicological Information
Occupationally Relevant Routes of Exposure
Inhalation No quantitative information found.
Ingestion Rat, LD50: 5000 mg/kg
Skin No quantitative information found.
Eye No quantitative information found.
Section 12: Ecological Information
Environmental Fate Possibly hazardous short term degradation products are not likely. However, long term degradation products may arise. The products of degradation may be more toxic.
Distribution and Persistence
in the Environment
No information found.
Bioaccumulation in
Aquatic Organisms
No information found.
Permissible Concentration
in Water
No information found.
Section 13: Disposal Considerations
Physical/Chemical Properties This material is a stable solid. Although not a listed RCRA hazardous waste, this material may exhibit one or more characteristics of a hazardous waste and require appropriate analysis to determine specific disposal requirements. Processing, use or contamination of this product may change the waste management options.
Recommended Disposal Method Where possible, re-blend spilled, unused, or off-specification materials with other suitable materials in support of waste minimization. Where this is not possible, dispose of material according to Federal (country-specific), state, and local requirements.
Empty Containers This product may be shipped in paper or nylon bags, steel drums, plastic or steel pails, or intermediate bulk containers. All residual material must be emptied and the containers recycled where possible. Where recycling is not possible, containers must be disposed of in accordance with Federal (country-specific), state, and local regulations. If questions exist about disposal, please contact the manufacturer for additional information.
Section 14: Transportation Information
Not regulated.
Section 15: Regulatory Information
TSCA 8(b) Inventory Ultramarine Blue
WHMIS Not controlled under WHMIS (Canada).
This MSDS has been prepared according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR.
Section 16: Labeling Information
Product Name Lapis Lazuli
Ingredients Sodium Alumino Sulfosilicate
Signal Word WARNING!
Hazard Description May be harmful if inhaled or ingested. May cause irritation to eyes and respiratory tract.
Precautions Do not get in eyes, on skin, or on clothing. Wash thoroughly after handling. Do not breathe dust. Keep container closed. Use only with adequate ventilation.
First Aid
Procedures
In case of contact, wipe off excess material from skin then immediately flush eyes or skin with plenty of water. Remove contaminated clothing and shoes. Wash clothing before reuse. If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. If swallowed, DO NOT INDUCE VOMITING. Never give anything by mouth to an unconscious person. In all cases call a physician if symptoms develop.
Fire Instructions This material is not flammable. Select fire extinguishment media for surrounding materials.
Spill or Leak
Procedures
Wear appropriate protective equipment. Limit foot and vehicular traffic to minimize agitation and dispersion. Employ a vacuum (equipped with a HEPA filter), broom and shovel, and wet sweeping for spill clean-up. Avoid creating dust. Do not allow this product or run-off to reach waterways.
Handling and
Storage Instructions
Wear specified elements of personal protective equipment, as defined in the Material Safety Data Sheet (MSDS), or follow location specific instructions for handling this product. Store in a cool, dry, well-ventilated area. Specific instructions concerning directions for use and handling may be found in the MSDS or may be supplied by the manufacturer.
Section 17: Other Information
HMIS Ratings Health: 2 (Moderate)
Flammability: 0 (None)
Reactivity: 0 (None)
Personal Protection: E
NFPA Ratings Health: 2 (Moderate)
Flammability: 0 (None)
Reactivity: 0 (None)
Date 24 August 2007
Disclaimer The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. Natural Pigments, LLC shall not be held liable for any damage resulting from handling or from contact with the above product.

Copyright 2005-2007 Natural Pigments, LLC. License granted to make unlimited paper copies for internal use only.
Here are items you recently viewed during your visit of Natural Pigments Recently Viewed
No recently views items
Clear All
Copyright © 2012-present Natural Pigments, Inc. All rights reserved.